Sectional garage sectional doors with torsion mechanism RSD02 China

Garage doors of the RSD02 China are designed for installation in openings of both small and medium sizes. They can be installed in rooms with a lintel (distance from the top edge of the opening to the nearest obstacle or ceiling) of 160 mm and side distances (from the edge of the opening to the wall) of 120 mm. The design of the guides allows this sectional doors to be installed in rooms with various architectural features. Opening dimensions: width — from 2 000 to 6 000 mm; height — from 1 800 to 3 000 mm. Garage doors can be equipped with a wicket door built into the door leaf.

Application:

Private garages
Utility rooms

Order with installation

Advantages

The absence of a cold bridge in the sandwich panel and sealing along the entire contour due to seals guarantee maximum thermal efficiency of the door.

Large selection of gate panels, more than 100 design options.

The gates are entirely manufactured in China at the DoorHan concern's own factories, taking into account the peculiarities of Chinese operating conditions.

The design, proven over years, and the safety margin of the components guarantee a long service life.

The absence of a cold bridge in the sandwich panel and sealing along the entire contour due to seals guarantee maximum thermal efficiency of the door.

Large selection of gate panels, more than 100 design options.

The gates are entirely manufactured in China at the DoorHan concern's own factories, taking into account the peculiarities of Chinese operating conditions.

The design, proven over years, and the safety margin of the components guarantee a long service life.

Design

Panel design

Surface type

Colors of the front surfaces of the panels

S-Line

V-Line

D-Line

M-Line

Cassete

S-Line (inner side)

Wood effect (external)

Stucco (external)

Stucco (internal)

RAL 9003 (white)

RAL 9006 (silver)

RAL 7004 (grey)

RAL 1014 (beige)

RAL 6005 (green)

RAL 5005 (blue)

RAL 7016 (anthracite)

RAL 3000 (red)

RAL 3005 (burgundy)

RAL 8017 (brown-red)

Golden Oak

Mahogany

Non-standard color according to RAL card (surcharge)

Equipment

Standard

Optional

Canvas made of energy-efficient sandwich panels 40 mm thick and reinforced for internal hinges and side supports.

A set of guides and corner posts made of galvanized steel has everything necessary for the installation of perforations.

Torsion mechanism designed for 25 000 cycles.

Box with installation kit, product data sheet and installation instructions.

The spring break protection device blocks the shaft, which prevents the door leaf from falling.

Acrylic window 607 x 202, black (art. DH85602). The special design ensures a tight fit to the door leaf, which protects it from freezing and heat loss. Black edging.

Acrylic window 627 x 327, black, industrial (art. DH85603). The special design ensures a tight fit to the door leaf, which protects it from freezing and heat loss. Black edging.

Acrylic window 452 x 302, white (art. DH85626). The special design ensures a tight fit to the door leaf, which protects it from freezing and heat loss. White edging.

Acrylic window 452 x 302, brown (art. DH85631). The special design ensures a tight fit to the door leaf, which protects it from freezing and heat loss. Brown edging.

Acrylic window 452 x 302, white with cross layout (art. DH85627). The special design ensures a tight fit to the door leaf, which protects it from freezing and heat loss. Stylistic insert in the shape of a cross. White edging.

Acrylic window 452 x 302, brown with a cross layout (art. DH85628). The special design ensures a tight fit to the door leaf, which protects it from freezing and heat loss. Stylistic insert in the shape of a cross. Brown edging.

Acrylic window 452 x 302, white with diamond layout (art. DH85629). The special design ensures a tight fit to the door leaf, which protects it from freezing and heat loss. Stylistic insert in the shape of a diamond. White edging.

Acrylic window 452 x 302, brown with diamond layout (art. DH85629). The special design ensures a tight fit to the door leaf, which protects it from freezing and heat loss. Stylistic insert in the shape of a diamond. Brown edging.

The cable break protection device is installed as a lower bracket on the door leaf. If the cable breaks, the mechanism is activated and prevents the door leaf from falling.

The gate has an improved design, is highly durable and has an aesthetic appearance. The minimum height of the shield is 2 130 mm.

A mechanical lock allows you to block the door leaf in the closed position both from inside the room and from the street.

A mechanical latch allows you to lock the gate from inside the room. It is simple and reliable.

Technical description

Size Table

Construction

Standard Construction

Specifications

Operating Conditions

Packaging

Parameters

Value

Opening width, mm

2 000–6 000

Opening height, mm

1 800–3 500

Headroom, mm

From 160

Sideroom clearance, mm

From 120

Gate leaf balancing system (spring-torsion mechanism)
End U-shaped support bracket
Top profile
Guides for the door leaf
Support with roller holder and roller
Corner post
Side cover
Spring break protection device
Ceiling mounting system
Upper support bracket
Upper seal
Loop
Door leaf made of sandwich panels
Gate valve
Bottom support bracket
Bottom profile with seal
Handle

Low rise, drum at the front.

Symbol, parameter name	Calculation formula
H, mm Opening height	H
h, mm Headroom height	≥ 160 (≥ 190 mm for drive)
B, mm Opening width	B
A, mm Angle track height	H + 54
Ab, mm Height of shaft axle and drum	≥ A + 59
A1, mm Vertical track height	А - 543
A2, mm Horizontal track height	А - 106
E, mm Horizontal track length	Н + 300
Db, mm Torsion spring operation space	Depends on the size of the opening and the weight of the shield
S, mm Minimum side room clearance	120
P, mm Door opener position	Н + 1 185
n, mm Clear opening	190 (without drive); 0...10 (with ceiling drive)

Standard lift.

Symbol, parameter name	Calculation formula
H, mm Opening height	H
h, mm Headroom height	R381: ≥ 420; R305: ≥ 350
B, mm Opening width	B
A, mm Angle track height	R381: H+235; R305: H+165
Ab, mm Height of shaft axle and drum	A + 97
A1, mm Vertical track height	R381: A - 580; R305: A - 490
A2, mm Horizontal track height	А - 110
E, mm Horizontal track length	R381: H+200; R305: H+250
Db, mm Torsion spring operation space	Depends on the size of the opening and the weight of the shield
S, mm Minimum side room clearance	120
P, mm Door opener position	Н + 1 060
Q, mm Shaft opener position	300

Parameter	Value	Notes
Heat transfer resistance of the fabric, m² * °C/W	1.13 (A)	The value depends on the size of the door, indicated for doors measuring 3 500 x 3 000 mm
Thermal conductivity, W/m·°С	0.88 (DIN4108)
Wind load, kg/sqm	2 class (EN12424:2000)
Tightness	4 class (EN12426:2000)
Водонепроницаемость	3 class (EN12425:2000)
Sound insulation, dB	< 35
Force of manual opening and closing, kg	Up to 25.5
Door leaf weight, kg/m²	11.2
Panel thickness, mm	40
Metal thickness, mm	0.35
Number of cycles	25 000

1. Sections of the door leaf must move smoothly along the guides, and the door itself must be balanced, i.e., its weight must be compensated by the torque of the springs.

2. Manual opening and closing of the gate is carried out only with the help of a handle.

3. When opening and closing the gate manually, do not apply much force to it. Sudden jerks are prohibited.

4. Make sure that people and animals are not in the area of the gate while it is operating.

5. It is strictly prohibited to move under the moving door leaf, as this can lead to injury.

6. Do not subject the gate to impacts or interfere with its free movement when opening and closing.

7. Make sure that there are no foreign objects or debris in the opening while the blade is moving. Their presence can lead to skewing and jamming of the door leaf.

8. Do not expose the guides and rollers to contamination, as this may impair smooth operation, and if there is an electric drive, this may lead to its overload and failure.

Packing in cardboard	Packaging features
Description	The guide system and panel of sectional doors have a rigid combined packaging made of cardboard and polystyrene foam, covered with stretch film; the installation kit is packed in a corrugated cardboard box and sealed with packaging film; All packages are equipped with information stickers containing order data, as well as the company logo
Contents	Five-layer cardboard, polystyrene foam, stretch film, tape
Width, mm	500–800
Height, mm	200–400
Length, mm	2 100–6 100
Gross weight, kg	Up to 200
Number of items in the packaging	Shield packaging — from 3 to 5 panels; package of guides - 1 guide system; packaging of components - box with complete set

Packing in cardboard box	Packaging features
Length, mm	550

Additional Information print

It is recommended to store sandwich panels in their original packaging in a horizontal position on a flat surface for no more than 6 months from the date of production in closed warehouses or under a canopy. The panels must be protected from direct sunlight, precipitation and contamination.

Installation

Mounting Options

Checking Dimensional Details

Surface mounting: the guide system is mounted on the walls and lintel from the inside of the opening.

To take the necessary indicators, a tape measure and a building level are enough. All measurements are taken indoors. Each value must be measured at least at three points (in extreme positions and in the center).
H is the height of the opening (distance from the floor to the top of the opening).
B is the width of the opening (the distance from the left to the right edge of the opening).
h — lintel (distance from the top of the opening to the ceiling) min 160 mm.
b1/ b2 — left/right side distance (distance from the corresponding edge of the opening to the obstacle) min 120 mm.
L is the depth of the room.
When measuring H and B, the largest value is taken as the final size.
When measuring h, b1, b2 and L, the smallest value is taken.
The difference in floor level across the entire width of the opening should not exceed 10 mm. It is necessary to ensure that the mounting plane (walls and ceiling) is maintained. The base for installing the guide system must be monolithic and durable; if this is not available, additional edging or the formation of an opening with metal products is required.